FDP Home Page / FDP Forum / FAQ's

The FDP is made possible by the following companies and individual members like you.
Please use the links below to show them we value their sponsorship.

Guitar Center

Apex Tube Matching

Musician's Friend

Yellowjackets Tube Converters

Sweetwater

Amazon

MOD KITS DIY

Antique Electronics Supply

WD Music

Jensen Loudspeakers

Amplified Parts


* God bless America and our men and women in uniform *

* Illegitimi non carborundum! *

If you benefit and learn from the FDP and enjoy our site, please help support us and become a Contributing Member or make a Donation today! The FDP counts on YOU to help keep the site going with an annual contribution. It's quick and easy with PayPal. Please do it TODAY!

Chris Greene, Host & Founder

LOST YOUR PASSWORD?

......................................................................

   
FDP Jam
Calendar
Find musicians
in your area!
  Search the Forums  

FDP Forum / Amp Mods, Repairs, and Projects / Preferred soldering temperature

STR87

Panama

Dec 27th, 2017 12:57 PM   Edit   Profile   Print Topic   Search Topic

Hi, just got a Weller wes51 soldering station for some amp work and would like to know a good all around temperature to dial in?
What are your preferences?

Peegoo
Contributing Member
**********
**********
******

Curled up

in the fecal position
Dec 27th, 2017 01:43 PM   Edit   Profile   Print Topic   Search Topic

I run my Hakko at 600-650f for most stuff. I'm using 60/40 rosin core solder.

For heavier stuff like cap cans and soldering to the chassis, more heat won't do the trick if the stick you have is slow to recover. It's best to have something that can sink a bunch of heat into the work very fast.

Like this.

Pinetree
Moderator Emeritus
(with many stars)

NW Pennsylvania

Dec 27th, 2017 07:37 PM   Edit   Profile   Print Topic   Search Topic

I run my Hakko about the same... maybe 700 for pots.

A wide chisel tip really helps for amp work.



Te 52

Laws of Physics

strictly enforced
Dec 27th, 2017 09:48 PM   Edit   Profile   Print Topic   Search Topic

When I worked in the electronics biz, the techs always ran their WESD51s around 725-750F, and I do the same. Get on, get off, fast. For pots, I change to a wide tip and max the Weller out to 850F.

(This message was last edited by Te 52 at 12:21 PM, Dec 28th, 2017)

Peegoo
Contributing Member
**********
**********
******

Curled up

in the fecal position
Dec 28th, 2017 12:42 AM   Edit   Profile   Print Topic   Search Topic

Here's a pretty good rundown on equipment and technique (link below).

Two important points about soldering sticks:

1. Never use a file or sandpaper on a new tip, because you will remove the copper tip's thin iron plating. Once that happens, the copper will corrode rather quickly and the tip will be ruined.

2. Many people use a wet sponge or wet paper towel to clean the tip between solder applications. This works, but it also sinks a lot of the heat out of the tip. It's better to use a brass sponge, because it cleans the tip without removing heat. This way the tip stays hot and it's ready to go. Solder won't stick to the brass wool, so it lasts for years. You can buy a brass wool tip-cleaning container for about $10, or you can go to your grocery store and get a brass scrubbing pad in the kitchen supplies aisle for a few bucks. Stuff a wad of it into a shot glass and you're off to the races: poke the tip of the stick into the brass once or twice and it's clean. Shake out the brass wool once in a while to keep it clean.

Big Clive walks you through the basics.

RicOkc

Nicoma Park, OK.

"Let the music do the talking"
Dec 28th, 2017 02:17 AM   Edit   Profile   Print Topic   Search Topic

I worked in the electronics industry for many years, including micro-soldering.

I usually ran the tip at 800 degrees. Fast & quick.

Peegoo
Contributing Member
**********
**********
******

Curled up

in the fecal position
Dec 28th, 2017 12:35 PM   Edit   Profile   Print Topic   Search Topic

If you are de-soldering with braid, you need to crank the heat up.

The temperature you use depends on how you solder (styles differ) and what you are soldering. The trick is to get in and out fast with the stick. If you leave it in place, you risk 'cooking' a component and damaging it.


I recently saw a vid where the techs weren't using hot air for re-work. They used a little halogen bulb and its heat radiation. It worked really well!

willie
Contributing Member
********

Too Near Atlanta GA

Amp Tech Emeritus
Dec 29th, 2017 11:50 AM   Edit   Profile   Print Topic   Search Topic

Also depends on the type of work being done (analog PTP tube type stuff, versus analog solid state thru hole, versus digital SMT, etc), plus the type of solder being used as well.

There is a world of knowledge to be learned and absorbed about soldering. I owe a lot to attending NASA Soldering School back in 1966 while working for Honeywell Aerospace...I thought I knew how to solder before I went there. :-)

willie

(This message was last edited by willie at 01:51 PM, Dec 29th, 2017)

avspecialist

USA/Connecticut

Bobby Roadrunner
Jan 2nd, 2018 06:04 AM   Edit   Profile   Print Topic   Search Topic

I run my station at 720.I use the Brass Wool to clean. I like the Dayton 4% Silver Solder.


STR87

Panama

Jan 2nd, 2018 02:59 PM   Edit   Profile   Print Topic   Search Topic

Thank's, will give those a try!


FDP Forum / Amp Mods, Repairs, and Projects / Preferred soldering temperature




Reply to this Topic
Display my email address             Lost your password?
Your Message:
Link Address (URL):
Link Title:




Moderators: Chris Greene  Iron Man  reverendrob  

FDP, LLC Privacy Policy: Your real name, username, and email
are held in confidence and not disclosed to any third parties, sold, or
used for anything other than FDP Forum registration unless you specifically authorize disclosure.

Furtkamp.com 
Internet Application Development

Copyright © 1999-2018 Fender Discussion Page, LLC   All Rights Reserved